A Worcester C7 fault code means the boiler couldn’t get its fan running, or couldn’t detect enough airflow, when it tried to fire up. When the control board can’t confirm the fan is clearing the flue, it locks out as a safety measure rather than attempting to light the burner. This is an internal fault, and the fix is a repair job for a Gas Safe registered engineer.
What Does C7 Mean?
On Worcester Bosch boilers such as the Greenstar i, C7 is shown with a three-digit cause code that narrows the fault down. You’ll usually see it next to the C7, or after pressing the info or return button:
- C7 214: the fan is not running.
- C7 217: the fan is not running, or there’s no airflow after a set time, which can also point to a blocked flue or air intake.
Note down which one you have before you call an engineer, because it changes what they check first. The wording and cause codes vary slightly between Worcester ranges, so it’s worth confirming against your own model’s manual.
The reason this fault exists at all comes down to how a condensing boiler works. The fan’s job is to draw combustion gases safely out of the boiler and away through the flue. If the fan cannot be confirmed as running when the boiler calls for heat, there is no safe way to let gas ignite, because the exhaust gases would have nowhere to go. The boiler’s electronics are built to notice this and lock out rather than take the risk, which is exactly what you are seeing when C7 appears on the display.
Common Causes
C7 is a symptom, not a single diagnosis. A handful of different faults inside the boiler can all produce the same code, and the only way to tell them apart is to test the fan and the parts connected to it.
| Cause | What it looks like |
|---|---|
| Failed fan | Completely silent at start-up, with no hum, click or movement at all, even though the boiler has power |
| Worn bearings | A rattling or grinding noise, or a slower, laboured start, in the days or weeks before the fault appeared |
| Wiring or connector fault | Intermittent starts with no obvious pattern, where the boiler sometimes fires normally and sometimes locks out |
| Control board fault | The fan has power reaching it, sometimes even a faint hum, but still does not spin up properly |
| Blocked flue or air intake | Usually shows as C7 217. Something is restricting the airflow, such as a bird’s nest, debris or ice around the flue terminal outside |
| Water damage | A leak near the fan housing or control board, often with visible staining or corrosion on the casing |
Several of these overlap in how they present, which is why a fan that “sounds fine” one day and silent the next is still worth a proper inspection rather than a guess. A connector that has simply worked loose over time, for example, can look identical from the outside to a fan that has actually failed, and the only reliable way to tell the two apart is for an engineer to test the fan with the connector reseated before deciding anything else needs replacing. Age plays a part too: a fan that has been running for several years is more likely to be worn than one from a boiler installed last winter, though a sudden knock to the boiler casing or a recent leak nearby can bring on the same fault at any age.
What You Can Safely Check Yourself
There is a short, genuinely safe list of checks before you book an engineer, and it is worth working through it in order:
- Note the cause code shown with C7 (214 or 217).
- Try a single reset, following the steps in your boiler’s user manual.
- Check the system’s cold pressure on the gauge and top up if the manual says it is low. If it reads high instead, see our guide to boiler pressure too high.
- Look for any obvious external leak around the boiler casing or nearby pipework.
- From the ground, look at the flue terminal outside for anything obviously blocking it. Don’t climb up or try to clear it yourself.
- Note whether you heard any unusual noise or felt vibration in the moment the boiler tried to ignite, since this detail helps an engineer narrow down the cause.
What you should not do is open the boiler’s casing, bypass a sensor or safety device, or keep pressing reset over and over hoping it clears on its own. None of these make the fan work again, and repeated resets on a genuine fan fault can mask a developing problem or put extra strain on the control board. If a single reset does not hold, stop there and move on to getting the fault looked at properly. If your boiler has stopped with no code on the display at all, our boiler not working guide is a better place to start.
When to Call a Gas Safe Engineer
Fan replacement, wiring repairs and control board diagnostics on a gas boiler are not DIY jobs, and by law they have to be carried out by an engineer on the gassaferegister.co.uk register. The Health and Safety Executive puts it plainly on hse.gov.uk:
“Anyone employed to work on gas appliances in domestic premises must be a Gas Safe registered engineer and competent in that area of gas work.”
Once an engineer is on site for a C7 fault, the work typically involves testing the fan itself, checking its wiring and connector for damage or a loose fit, and inspecting the control board to see whether it is sending power to the fan correctly. Only once each of these has been tested in turn can the real cause, rather than just the symptom, be confirmed.
It is worth mentioning why this cannot be shortcut. A fan that looks fine when spun by hand can still fail under load, and a control board that powers other parts of the boiler correctly can still be sending the wrong signal to the fan alone. Testing in sequence, rather than swapping the first likely-looking part, is what stops a repair turning into several separate call-outs for parts that were never actually faulty.
How Much Does a Repair Cost?
There is no fixed price for a C7 repair, because the cost depends entirely on what the engineer finds once they have tested the fan, wiring and control board. A worn fan bearing is a different job from a faulty control board, and the correct price only becomes clear after that diagnosis has been done. BeFix charges for the engineer’s time at £95 per hour between 7am and 5pm, £125 per hour between 5pm and 9pm, and £160 per hour between 9pm and 7am, all plus VAT. There’s no separate call-out fee: the hourly rate starts when the engineer arrives, with a minimum charge of one hour, and any extra time is charged in 30-minute increments. Parts are billed separately and confirmed once the fault has been diagnosed.
A C7 fault doesn’t wait for office hours, which is why the rate is banded by time rather than fixed throughout the day or night. On an older boiler where the fan and the control board both need replacing, it can be worth comparing the repair with boiler installation London prices before deciding.
C1, C6 and C7: The Fan Family
C1, C6 and C7 all relate to the same fan, but each describes a different moment where something has gone wrong, which is why they are worth telling apart rather than treating as interchangeable.
| Code | What it relates to | When it appears |
|---|---|---|
| C1 (cause code 264) | Airflow stopping during operation, often because the fan has stopped | While the boiler is already running |
| C6 (215 / 216) | Fan running too fast (215) or too slow (216) | During operation, as the fan struggles to hold the correct speed |
| C7 (214 / 217) | Fan not running, or no airflow detected | At start-up, before the boiler can safely fire |
Because the exact wording and sub-codes shift between Worcester ranges, it is still worth checking your own model’s manual to confirm which of these applies, rather than assuming the code means the same thing on every Worcester boiler.
Seeing C1 or C6 rather than C7 does not change the first steps much, since the same checks above still apply. What changes is what the engineer tests first: a C1 or C6 fault points them toward the fan while the system is running, where a C7 fault points them toward what happens in the seconds before the burner is due to light. If the display shows EA instead, the boiler tried to light but couldn’t detect a flame, which is covered in our guide to the Worcester boiler EA 227 fault code.
If your boiler is showing C7, or any other fan-related fault, a gas-safe-registered engineer can confirm the cause and carry out the repair safely. BeFix, Gas Safe registered under licence 967796, covers boiler repair in London for faults like this one.
Frequently Asked Questions
What does C7 mean?
C7 means the boiler’s fan did not run, or no airflow was detected, when the boiler tried to start up. On models such as the Greenstar i, C7 214 means the fan isn’t running and C7 217 means the fan isn’t running or the airflow is blocked. Either way, the boiler locks out rather than allowing the burner to light.
Can I reset the boiler myself?
Yes, you can try one reset following your boiler’s manual, and it is a safe first step. If the fault clears and stays clear, that is a good sign, but if C7 comes back, resetting again will not fix the underlying fan problem and you should book an engineer instead.
Is it safe to keep using the boiler?
No. The lockout exists because the boiler cannot confirm the fan is safely clearing combustion gases, and there’s no safe way around that. Leave it switched off at the fault and have the fan and control board tested by a Gas Safe engineer.
Is C7 dangerous?
The boiler locking out on C7 is the safety system doing its job, since it stops the burner lighting without the fan confirmed as clearing exhaust gases. The fault itself is not something to ignore, though, and should be diagnosed and repaired properly.
How long does a C7 repair take?
It depends on the cause. A loose connector or a wiring fault can often be fixed on the same visit, while a failed fan or control board may take longer if the part isn’t already on the van and needs ordering. The engineer will give a realistic timeframe once they’ve tested the fan and seen what’s actually wrong.
Is C7 the same as C6?
No. C7 is about the fan failing to run at start-up, while C6 relates to the fan running at the wrong speed once the boiler is already operating. Both point to a problem with the fan, but they describe different moments in the boiler’s start-up and running cycle.


Leave A Comment