A21 on a Worcester wireless thermostat means the radio signal between the thermostat and the receiver at the boiler has been lost. Without that signal, the boiler is not told when the home needs heat, so the heating stops responding. It is rarely a fault with the boiler itself, and most cases clear with fresh batteries or by moving the thermostat.
| Already tried new batteries? | Do this next | Still not fixed? |
|---|---|---|
| No | Fit fresh batteries and wait a minute or two for A21 to clear | Move the thermostat closer to the receiver |
| Yes, same spot | Move the thermostat closer to the receiver and test again | Book a Gas Safe registered engineer if it returns |
| Yes, closer too | The thermostat, receiver or wiring is the likely cause | Book a Gas Safe registered engineer |
What Does A21 Mean?
Worcester’s manual for its Comfort RF wireless controls describes A21 as a loss of RF (radio frequency) signal. A wireless thermostat is not connected to the boiler by a cable. It sends a small radio signal to a receiver, usually fitted on or near the boiler, and the receiver tells the boiler when to fire. A21 appears when the receiver stops hearing from the thermostat. Wording can vary between control models, so check the fault code table in your own manual.
This narrows down where to look. A21 is a communication fault between two units, not a problem with the boiler’s gas valve, heat exchanger or water pressure. In almost every case the fix starts with the thermostat, its batteries and its position.
A21 After a Power Cut or Switch-On
A21 is also shown when the system is first switched on, until the thermostat and receiver have found each other again. Worcester’s manual says to allow up to a minute after the power comes back for the two units to start communicating. If you see A21 straight after a power cut, or after the boiler has been switched off at the wall, wait a minute or two before doing anything else.
Common Causes
| Cause | What it looks like |
|---|---|
| Low or flat batteries | Thermostat display dim or blank, or A21 returning every few days |
| Out of range | Thermostat a long way from the receiver, or several walls between them |
| Boiler in a loft or garage | Signal struggles to reach the receiver from the living space |
| Radio interference | Fault appears at certain times, or after a new wireless device was added |
| No power at the boiler | Boiler display off, or a tripped switch or fuse |
| Faulty thermostat or receiver | A21 returns even with new batteries and the thermostat close to the receiver |
If your heating cuts in and out instead of stopping completely, a weak thermostat signal can be one cause. Our guide on why does my boiler keep turning on and off covers that and the other usual reasons.
A21, A23 or A24?
Worcester’s wireless controls use a few similar codes, and they point to different fixes.
| Code | What it means | Usual fix |
|---|---|---|
| A21 | Radio signal lost between the thermostat and the receiver | New batteries, moving the thermostat, or checking the receiver |
| A23 | The thermostat’s own temperature sensor has failed | Replacing the wireless thermostat |
| A24 | Another wireless thermostat on the same system has a fault | Checking the other thermostats for their own fault codes |
What You Can Safely Check Yourself
- Check the boiler has power and its display is on.
- Change the thermostat batteries, even if the display still looks bright. You may need to set the time or programme again afterwards.
- Wait a minute or two for the thermostat and receiver to reconnect.
- Move the thermostat closer to the receiver for a day and see if the fault clears. Your manual explains how to test the signal strength from different spots.
- Check whether anything new sits between the thermostat and the receiver, such as a metal cabinet, a large appliance or another wireless device.
Do not open the boiler casing, and do not keep resetting the boiler to make the code go away. Repeated resets will not fix a faulty thermostat, receiver or wiring.
When to Call a Gas Safe Engineer
If fresh batteries and a closer position do not fix it, book an engineer. The thermostat itself runs on batteries, but the receiver is wired into the boiler, so testing it, moving it or fitting a wired thermostat means working at the boiler. If your boiler is in a loft or garage, Worcester’s manual suggests wiring the receiver to a wall plate in a better position, which is also a job for an engineer.
An engineer will check the signal strength, test the receiver and its wiring, and confirm whether the thermostat or the receiver has failed, so you do not buy the wrong replacement. You can check any engineer’s registration by postcode or licence number at gassaferegister.co.uk before they start.
| Task | Who it’s for |
|---|---|
| New batteries, moving the thermostat, checking power | Most homeowners, no tools needed |
| Confirming a faulty thermostat or receiver | Gas Safe registered engineer |
| Moving the receiver or fitting a wired thermostat | Gas Safe registered engineer |
BeFix (Gas Safe 967796) offers same-day boiler repair in London, including thermostat and receiver faults like A21.
How Much Does an A21 Repair Cost?
There is no single price, because it depends on the cause. New batteries cost very little. A replacement thermostat or receiver, or a switch to a wired thermostat, takes longer and involves parts. An engineer can only give an accurate figure once they have found which part has failed.
BeFix charges £95 an hour between 7am and 5pm, £125 an hour between 5pm and 9pm, and £160 an hour between 9pm and 7am, all plus VAT, with no call-out fee. Parts are costed separately and confirmed once the fault has been diagnosed.
Frequently Asked Questions
What does A21 mean?
A21 means the wireless radio signal between your Worcester thermostat and its receiver has been lost. The boiler cannot see a request for heat, so the heating stops responding until the link is restored. It is almost always a thermostat or receiver issue, not a fault with the boiler itself.
Why does A21 show after a power cut?
A21 appears at switch-on until the thermostat and receiver reconnect. Worcester’s manual says to allow up to a minute for this. If it clears on its own, there is nothing wrong.
I put new batteries in but A21 is back the next morning. Is the thermostat dead?
Not necessarily. If A21 clears with fresh batteries and then returns, range or interference is more likely than a flat battery. Try the thermostat closer to the receiver first. If it still comes back at close range, the thermostat or receiver may be faulty, and an engineer can test the signal before you buy a replacement.
Does A21 affect hot water?
A21 affects the signal from the room thermostat, which controls the heating. On a combi boiler, hot water is heated on demand, so it usually keeps working. If you have a hot water cylinder, it depends on how your controls are set up, so check whether your hot water is still heating.
Is it safe to keep using the boiler?
Yes. A21 is a communication fault, not a safety lockout, so the boiler is not unsafe. The heating will not respond to the thermostat until the link is back, so it is still worth sorting out quickly.
Can interference cause A21?
Yes. Thick walls, metal furniture and other wireless devices can weaken the signal between the thermostat and receiver. It is more likely if A21 only appears at certain times or when the thermostat is in certain rooms.
Is A21 serious?
No, A21 is one of the more minor Worcester codes. It relates to the thermostat signal, not to gas, pressure or combustion. Most cases clear with new batteries or by moving the thermostat.
Will a wired thermostat fix A21?
Yes, a wired thermostat removes the radio link, so A21 cannot return. It is a bigger job than changing batteries, usually involving new cabling, so ask an engineer whether a simpler fix will do first.


Leave A Comment